Workplace Eye Safety in Ireland

24 Mar 2025 | Health & Safety

Health & Safety · Practical guide

Workplace Eye Safety in Ireland

Review workplace eye hazards, prevention and protective equipment as part of a risk assessment.

By · HSEQ · Originally published 24 March 2025 · Reviewed 4 November 2026

Worker adjusting hearing protection while wearing safety glasses

Start with the work that can harm the eyes

Workplace eye safety starts with understanding how a task can expose employees and other people to harm. Cutting, grinding, chemical handling, cleaning and specialist light sources create different hazards. A single pair of safety glasses or a general awareness course cannot be assumed suitable for all of them.

Look at normal production, cleaning, maintenance and unusual tasks. Include people who pass nearby, temporary staff and contractors. The purpose of the assessment is to choose effective controls and make sure they remain usable during real work, including busy periods and changes of shift.

This guide explains five practical reasons to review eye safety and the actions that turn an eyewear policy into an effective workplace arrangement. It is intended to support your assessment, equipment selection and staff instruction. Specialist tasks need advice appropriate to the hazard.

1. Identify hazards before choosing protection

List the tasks and the type of exposure they can create. Flying particles, splashes, dust and optical radiation need different consideration. Review the equipment instructions and, for chemicals, the relevant safety data sheets. Ask staff where exposure is possible, including when clearing a blockage, changing a container or cleaning up.

  • Identify where material may be projected or splashed and who could be in its path.
  • Check whether nearby work changes the risk, including work by contractors.
  • Consider cleaning and maintenance as well as normal operation.
  • Record the controls already used and any difficulty staff have using them.

Begin with ways to eliminate or reduce the hazard through the process, equipment or layout. Suitable guarding, enclosure or a changed method may protect more people and depend less on individual action. Personal protection addresses remaining risk; it should not excuse a missing or defective engineering control.

The HSA guidance on personal protective equipment explains its place in workplace risk control.

2. Match eye protection to the actual hazard

Protective spectacles, goggles and face protection have different capabilities. Select equipment for the identified hazard and the person using it, with competent advice and the manufacturer’s instructions where needed. Do not assume that ordinary prescription spectacles provide the protection required for a hazardous task.

Check how the chosen equipment works with other required PPE. A worker may also need a helmet, hearing protection or respiratory protection; the items need to function together without compromising fit or visibility. Where prescription correction is needed, plan a suitable protective solution rather than leaving the employee to improvise.

Specialist activities such as welding or laser work require protection appropriate to that activity. Generic eyewear should not be treated as adequate without checking the specification against the risk. The UK HSE’s technical guidance on choosing PPE describes common eye hazards and selection considerations; Irish legal arrangements should be checked against HSA guidance.

Involve the people who will wear the equipment in the selection process. Record problems such as fogging, poor fit or interference with other equipment and resolve them through suitable selection and work arrangements. A rule that staff cannot practically follow needs attention.

Worker wearing protective glasses and a hard hat in a warehouse

3. Make correct use straightforward

Provide the specified protection where it is needed, with a clear arrangement for replacements. Explain when and where it must be worn and demonstrate how to fit, inspect, clean and store it according to the manufacturer’s instructions. Check understanding through practical use rather than relying only on a signed attendance sheet.

Build checks into the work routine. Damaged, badly scratched or contaminated equipment may no longer provide the intended protection or may impair the wearer’s view. Staff need to know how to report a problem and obtain a suitable replacement before continuing an affected task.

Visitors and contractors also need clear information about controlled areas and required protection. Agree who supplies equipment and who checks that it is suitable. A temporary job should receive the same attention to its actual hazards as routine work.

A useful supervisor check is to ask an employee to explain the hazard, show the protection they use and describe what they would do if it were damaged. That short conversation can expose gaps that a stock count will miss.

4. Prepare for an incident and learn from near misses

Include foreseeable eye incidents in the workplace emergency and first-aid arrangements. Establish how staff will raise the alarm, obtain trained assistance and reach any emergency equipment specified by the assessment. Keep the relevant chemical and equipment information accessible to those who need it.

Do not wait for a serious injury before reviewing the task. A splash that misses a person, a particle striking a screen or repeated damage to eye protection may reveal a weakness in the method or controls. Record what happened and consider the conditions that allowed it, rather than stopping at a reminder to be careful.

If a chemical, machine, product or work method changes, revisit the assessment and instructions. Check whether the existing protection is still suitable and whether staff need further instruction before the revised task starts. Emergency equipment and response arrangements may need review at the same time.

5. Keep management checks focused on prevention

Treat eye safety as part of normal work planning, purchasing and supervision. A purchasing decision can affect exposure for years: new equipment, chemicals and protective equipment should be reviewed for suitability before they enter use. Allocate responsibility for maintenance and replacement so that a known defect does not remain unresolved.

Useful measures include outstanding control actions, recurring equipment problems and whether staff can explain the required precautions. Low incident numbers alone do not show that exposure is controlled; they should be considered alongside observations and employee feedback.

For example, a workshop may discover that staff remove goggles because they fog while cleaning equipment. The useful response is to review the task, ventilation, selected protection and compatibility, and test an improved arrangement. Simply issuing another reminder leaves the practical reason for removal unresolved.

Record the agreed action, who will complete it and how its effectiveness will be checked. Include changes in the relevant local instruction and make sure all affected shifts receive the update.

Connect eye safety with the wider workplace plan

Eye protection sits alongside other controls rather than operating as a separate checklist. Review nearby noise hazards, handling tasks and emergency arrangements where they affect the same work area. Our workplace noise guide and HSA inspection preparation guide provide related planning questions.

To discuss suitable awareness training or support with workplace procedures, contact AcornStar or explore our HSEQ consultancy services. Confirm the available training and its scope against the specific tasks your team performs.

Put the guidance into practice.

Discuss the training and procedures your team needs for its everyday work.

Talk to AcornStar →

Keep reading

More insights from AcornStar

Train smarter

Put these insights into practice with certified online training

Flexible, expert-led courses your team can complete on any device — backed by HSEQ consultancy when you need it.